MoTeC M150 pinout
ecurecovery.com/pinouts/motec/m150 · Every pin checked against 3 MoTeC documents · data checked 2026-11-01
Pinout
MoTeC M150 pinout
Every pin of the 34-pin A, 26-pin B, 34-pin C, and 26-pin D connectors, with MoTeC's own pin names. Tap a pin to see what it does.
Every pin checked against 3 MoTeC documentsPick any pin on the drawing or in the table to see its function and the documents it was checked in.
MoTeC M150 connector A pinout (34-pin)
Mating connector: Tyco Superseal 34 Position Keying 2 – MoTeC #65067
| Pin | Function | MoTeC note |
|---|---|---|
| A01 | Analogue Temperature Input 5 (AT5) | 1k Pull up to SEN_5V_C |
| A02 | Analogue Temperature Input 6 (AT6) | 1k Pull up to SEN_5V_C |
| A03 | Analogue Voltage Input 15 (AV15) | |
| A04 | Analogue Voltage Input 16 (AV16) | |
| A05 | Analogue Voltage Input 17 (AV17) | |
| A06 | Low Side Ignition 9 (IGN_LS9) | |
| A07 | Low Side Ignition 10 (IGN_LS10) | |
| A08 | Low Side Ignition 11 (IGN_LS11) | |
| A09 | Low Side Ignition 12 (IGN_LS12) | |
| A10 | Sensor 5.0V C (SEN_5V0_C1) | |
| A11 | Lambda Narrow Input 1 (LA_NB1) | |
| A12 | Lambda Narrow Input 2 (LA_NB2) | |
| A13 | Knock Input 3 (KNOCK3) | |
| A14 | Knock Input 4 (KNOCK4) | |
| A15 | Digital Input 2 (DIG2) | |
| A16 | Digital Input 3 (DIG3) | |
| A17 | Digital Input 4 (DIG4) | |
| A18 | Sensor 5.0V C (SEN_5V0_C2) | |
| A19 | Sensor 5.0V B (SEN_5V0_B2) | |
| A20 | LIN Bus (LIN) | |
| A21 | RS232 Receive (RS232_RX) | |
| A22 | RS232 Transmit (RS232_TX) | |
| A23 | Digital Input 1 (DIG1) | |
| A24 | Battery Negative (BAT_NEG3) | |
| A25 | Battery Negative (BAT_NEG4) | |
| A26 | Sensor 0V C (SEN_0V_C1) | |
| A27 | Sensor 0V C (SEN_0V_C2) | |
| A28 | CAN Bus 3 High (CAN3_HI) | |
| A29 | CAN Bus 3 Low (CAN3_LO) | |
| A30 | CAN Bus 2 High (CAN2_HI) | |
| A31 | CAN Bus 2 Low (CAN2_LO) | |
| A32 | Battery Negative (BAT_NEG5) | |
| A33 | Sensor 0V B (SEN_0V_B1) | |
| A34 | Sensor 0V A (SEN_0V_A1) |
MoTeC M150 connector B pinout (26-pin)
Mating connector: Tyco Superseal 26 Position Keying 3 – MoTeC #65068
| Pin | Function | MoTeC note |
|---|---|---|
| B01 | Half Bridge Output 9 (OUT_HB9) | |
| B02 | Half Bridge Output 10 (OUT_HB10) | |
| B03 | Universal Digital Input 8 (UDIG8) | |
| B04 | Universal Digital Input 9 (UDIG9) | |
| B05 | Universal Digital Input 10 (UDIG10) | |
| B06 | Universal Digital Input 11 (UDIG11) | |
| B07 | Universal Digital Input 12 (UDIG12) | |
| B08 | Low Side Injector 5 (INJ_LS5) | |
| B09 | Low Side Injector 3 (INJ_LS3) | |
| B10 | Analogue Voltage Input 9 (AV9) | |
| B11 | Analogue Voltage Input 10 (AV10) | |
| B12 | Analogue Voltage Input 11 (AV11) | |
| B13 | Battery Positive (BAT_POS) | |
| B14 | Low Side Injector 6 (INJ_LS6) | |
| B15 | Low Side Injector 4 (INJ_LS4) | |
| B16 | Analogue Voltage Input 12 (AV12) | |
| B17 | Analogue Voltage Input 13 (AV13) | |
| B18 | Analogue Voltage Input 14 (AV14) | |
| B19 | Battery Positive (BAT_POS) | |
| B20 | Half Bridge Output 7 (OUT_HB7) | |
| B21 | Half Bridge Output 8 (OUT_HB8) | |
| B22 | Peak Hold Injector 9 (INJ_PH9) | |
| B23 | Peak Hold Injector 10 (INJ_PH10) | |
| B24 | Peak Hold Injector 11 (INJ_PH11) | |
| B25 | Peak Hold Injector 12 (INJ_PH12) | |
| B26 | Sensor 5.0V A (SEN_5V0_A) |
MoTeC M150 connector C pinout (34-pin)
Mating connector: Tyco Superseal 34 Position Keying 1 – MoTeC #65044
| Pin | Function | MoTeC note |
|---|---|---|
| C01 | Half Bridge Output 2 (OUT_HB2) | |
| C02 | Sensor 5.0V A (SEN_5V0_A) | |
| C03 | Low Side Ignition 1 (IGN_LS1) | |
| C04 | Low Side Ignition 2 (IGN_LS2) | |
| C05 | Low Side Ignition 3 (IGN_LS3) | |
| C06 | Low Side Ignition 4 (IGN_LS4) | |
| C07 | Low Side Ignition 5 (IGN_LS5) | |
| C08 | Low Side Ignition 6 (IGN_LS6) | |
| C09 | Sensor 5.0V B (SEN_5V0_B) | |
| C10 | Battery Negative (BAT_NEG1) | |
| C11 | Battery Negative (BAT_NEG2) | |
| C12 | Low Side Ignition 7 (IGN_LS7) | |
| C13 | Low Side Ignition 8 (IGN_LS8) | |
| C14 | Analogue Voltage Input 1 (AV1) | |
| C15 | Analogue Voltage Input 2 (AV2) | |
| C16 | Analogue Voltage Input 3 (AV3) | |
| C17 | Analogue Voltage Input 4 (AV4) | |
| C18 | Half Bridge Output 1 (OUT_HB1) | |
| C19 | Peak Hold Injector 1 (INJ_PH1) | |
| C20 | Peak Hold Injector 2 (INJ_PH2) | |
| C21 | Peak Hold Injector 3 (INJ_PH3) | |
| C22 | Peak Hold Injector 4 (INJ_PH4) | |
| C23 | Low Side Injector 1 (INJ_LS1) | |
| C24 | Low Side Injector 2 (INJ_LS2) | |
| C25 | Analogue Voltage Input 5 (AV5) | |
| C26 | Battery Positive (BAT_POS) | |
| C27 | Peak Hold Injector 5 (INJ_PH5) | |
| C28 | Peak Hold Injector 6 (INJ_PH6) | |
| C29 | Peak Hold Injector 7 (INJ_PH7) | |
| C30 | Peak Hold Injector 8 (INJ_PH8) | |
| C31 | Half Bridge Output 3 (OUT_HB3) | |
| C32 | Half Bridge Output 4 (OUT_HB4) | |
| C33 | Half Bridge Output 5 (OUT_HB5) | |
| C34 | Half Bridge Output 6 (OUT_HB6) |
MoTeC M150 connector D pinout (26-pin)
Mating connector: Tyco Superseal 26 Position Keying 1 – MoTeC #65045
| Pin | Function | MoTeC note |
|---|---|---|
| D01 | Universal Digital Input 1 (UDIG1) | |
| D02 | Universal Digital Input 2 (UDIG2) | |
| D03 | Analogue Temperature Input 1 (AT1) | 1k Pull up to SEN_5V_A |
| D04 | Analogue Temperature Input 2 (AT2) | 1k Pull up to SEN_5V_A |
| D05 | Analogue Temperature Input 3 (AT3) | 1k Pull up to SEN_5V_B |
| D06 | Analogue Temperature Input 4 (AT4) | 1k Pull up to SEN_5V_B |
| D07 | Knock Input 1 (KNOCK1) | |
| D08 | Universal Digital Input 3 (UDIG3) | |
| D09 | Universal Digital Input 4 (UDIG4) | |
| D10 | Universal Digital Input 5 (UDIG5) | |
| D11 | Universal Digital Input 6 (UDIG6) | |
| D12 | Battery Backup (BAT_BAK) | |
| D13 | Knock Input 2 (KNOCK2) | |
| D14 | Universal Digital Input 7 (UDIG7) | |
| D15 | Sensor 0V A (SEN_0V_A) | |
| D16 | Sensor 0V B (SEN_0V_B) | |
| D17 | CAN Bus 1 High (CAN1_HI) | |
| D18 | CAN Bus 1 Low (CAN1_LO) | |
| D19 | Sensor 6.3V (SEN_6V3) | |
| D20 | Analogue Voltage Input 6 (AV6) | |
| D21 | Analogue Voltage Input 7 (AV7) | |
| D22 | Analogue Voltage Input 8 (AV8) | |
| D23 | Ethernet Transmit+ (ETH_TX+) | Ethernet |
| D24 | Ethernet Transmit- (ETH_TX-) | Ethernet Green |
| D25 | Ethernet Receive+ (ETH_RX+) | Ethernet |
| D26 | Ethernet Receive- (ETH_RX-) | Ethernet |
MoTeC M150 pins at a glance
- Which pins are CAN on the MoTeC M150?
- CAN Bus 3 High (CAN3_HI): pin A28. CAN Bus 3 Low (CAN3_LO): pin A29. CAN Bus 2 High (CAN2_HI): pin A30. CAN Bus 2 Low (CAN2_LO): pin A31. CAN Bus 1 High (CAN1_HI): pin D17. CAN Bus 1 Low (CAN1_LO): pin D18.
- Which pins are the injector outputs on the MoTeC M150?
- Low Side Injector 5 (INJ_LS5): pin B08. Low Side Injector 3 (INJ_LS3): pin B09. Low Side Injector 6 (INJ_LS6): pin B14. Low Side Injector 4 (INJ_LS4): pin B15. Peak Hold Injector 9 (INJ_PH9): pin B22. Peak Hold Injector 10 (INJ_PH10): pin B23. Peak Hold Injector 11 (INJ_PH11): pin B24. Peak Hold Injector 12 (INJ_PH12): pin B25. Peak Hold Injector 1 (INJ_PH1): pin C19. Peak Hold Injector 2 (INJ_PH2): pin C20. Peak Hold Injector 3 (INJ_PH3): pin C21. Peak Hold Injector 4 (INJ_PH4): pin C22. Low Side Injector 1 (INJ_LS1): pin C23. Low Side Injector 2 (INJ_LS2): pin C24. Peak Hold Injector 5 (INJ_PH5): pin C27. Peak Hold Injector 6 (INJ_PH6): pin C28. Peak Hold Injector 7 (INJ_PH7): pin C29. Peak Hold Injector 8 (INJ_PH8): pin C30.
- Which pins are the ignition outputs on the MoTeC M150?
- Low Side Ignition 9 (IGN_LS9): pin A06. Low Side Ignition 10 (IGN_LS10): pin A07. Low Side Ignition 11 (IGN_LS11): pin A08. Low Side Ignition 12 (IGN_LS12): pin A09. Low Side Ignition 1 (IGN_LS1): pin C03. Low Side Ignition 2 (IGN_LS2): pin C04. Low Side Ignition 3 (IGN_LS3): pin C05. Low Side Ignition 4 (IGN_LS4): pin C06. Low Side Ignition 5 (IGN_LS5): pin C07. Low Side Ignition 6 (IGN_LS6): pin C08. Low Side Ignition 7 (IGN_LS7): pin C12. Low Side Ignition 8 (IGN_LS8): pin C13.
- Which pins are ground on the MoTeC M150?
- Battery Negative (BAT_NEG3): pin A24. Battery Negative (BAT_NEG4): pin A25. Sensor 0V C (SEN_0V_C1): pin A26. Sensor 0V C (SEN_0V_C2): pin A27. Battery Negative (BAT_NEG5): pin A32. Sensor 0V B (SEN_0V_B1): pin A33. Sensor 0V A (SEN_0V_A1): pin A34. Battery Negative (BAT_NEG1): pin C10. Battery Negative (BAT_NEG2): pin C11. Sensor 0V A (SEN_0V_A): pin D15. Sensor 0V B (SEN_0V_B): pin D16.
- Which pins power the MoTeC M150?
- Battery Positive (BAT_POS): pins B13, B19, C26.
- Which pins are the sensor supplies on the MoTeC M150?
- Sensor 5.0V C (SEN_5V0_C1): pin A10. Sensor 5.0V C (SEN_5V0_C2): pin A18. Sensor 5.0V B (SEN_5V0_B2): pin A19. Sensor 5.0V A (SEN_5V0_A): pins B26, C02. Sensor 5.0V B (SEN_5V0_B): pin C09.
MoTeC M150 pinout sheet
A printable sheet with every pin, made from the checked data on this page.
Where this comes from
Only MoTeC's own documents. Pin names and notes are written exactly as MoTeC writes them.
MoTeC datasheet
MoTeC product page (pinout tables)
MoTeC hardware manual
Plug drawing: TE Connectivity customer drawing (used for the drawing only)Third party
How we checked it
- We start from MoTeC's datasheet for this ECU.
- We read every pin again on MoTeC's product page for the ECU, and in its hardware manual where that covers the ECU. A script compares them, pin by pin.
- A pin is only shown when its pin name and full name match in every document. MoTeC sets no standard wire colours, so none are shown.
- The notes are MoTeC's own words, shown when two of its documents print them alike.
ECU Recovery is not affiliated with MoTeC. MoTeC and its product names are trademarks of MoTeC. If your harness came with its own diagram, check your wiring against it.
More MoTeC pinouts
Map locked with a password?
We unlock Haltech, MaxxECU, LinkECU, Vi-PEC, ECUMaster, Emtron and FuelTech maps. You see proof from your own file first and only pay $159.99 if it works.
Unlock a map