MoTeC M130 pinout
ecurecovery.com/pinouts/motec/m130 · Every pin checked against 3 MoTeC documents · data checked 2026-11-01
MoTeC M130 pinout
Every pin of the 34-pin A and 26-pin B connectors, with MoTeC's own pin names. Tap a pin to see what it does.
Every pin checked against 3 MoTeC documentsPick any pin on the drawing or in the table to see its function and the documents it was checked in.
MoTeC M130 connector A pinout (34-pin)
Mating connector: Tyco Superseal 34 Position Keying 1 – MoTeC #65044
| Pin | Function | MoTeC note |
|---|---|---|
| A01 | Half Bridge Output 2 (OUT_HB2) | |
| A02 | Sensor 5.0V A (SEN_5V0_A) | |
| A03 | Low Side Ignition 1 (IGN_LS1) | |
| A04 | Low Side Ignition 2 (IGN_LS2) | |
| A05 | Low Side Ignition 3 (IGN_LS3) | |
| A06 | Low Side Ignition 4 (IGN_LS4) | |
| A07 | Low Side Ignition 5 (IGN_LS5) | |
| A08 | Low Side Ignition 6 (IGN_LS6) | |
| A09 | Sensor 5.0V B (SEN_5V0_B) | |
| A10 | Battery Negative (BAT_NEG1) | |
| A11 | Battery Negative (BAT_NEG2) | |
| A12 | Low Side Ignition 7 (IGN_LS7) | |
| A13 | Low Side Ignition 8 (IGN_LS8) | |
| A14 | Analogue Voltage Input 1 (AV1) | |
| A15 | Analogue Voltage Input 2 (AV2) | |
| A16 | Analogue Voltage Input 3 (AV3) | |
| A17 | Analogue Voltage Input 4 (AV4) | |
| A18 | Half Bridge Output 1 (OUT_HB1) | |
| A19 | Peak Hold Injector 1 (INJ_PH1) | |
| A20 | Peak Hold Injector 2 (INJ_PH2) | |
| A21 | Peak Hold Injector 3 (INJ_PH3) | |
| A22 | Peak Hold Injector 4 (INJ_PH4) | |
| A23 | Low Side Injector 1 (INJ_LS1) | |
| A24 | Low Side Injector 2 (INJ_LS2) | |
| A25 | Analogue Voltage Input 5 (AV5) | |
| A26 | Battery Positive (BAT_POS) | |
| A27 | Peak Hold Injector 5 (INJ_PH5) | |
| A28 | Peak Hold Injector 6 (INJ_PH6) | |
| A29 | Peak Hold Injector 7 (INJ_PH7) | |
| A30 | Peak Hold Injector 8 (INJ_PH8) | |
| A31 | Half Bridge Output 3 (OUT_HB3) | |
| A32 | Half Bridge Output 4 (OUT_HB4) | |
| A33 | Half Bridge Output 5 (OUT_HB5) | |
| A34 | Half Bridge Output 6 (OUT_HB6) |
MoTeC M130 connector B pinout (26-pin)
Mating connector: Tyco Superseal 26 Position Keying 1 – MoTeC #65045
| Pin | Function | MoTeC note |
|---|---|---|
| B01 | Universal Digital Input 1 (UDIG1) | |
| B02 | Universal Digital Input 2 (UDIG2) | |
| B03 | Analogue Temperature Input 1 (AT1) | 1k Pullup to SEN_5V_B |
| B04 | Analogue Temperature Input 2 (AT2) | 1k Pullup to SEN_5V_B |
| B05 | Analogue Temperature Input 3 (AT3) | 1k Pullup to SEN_5V_A |
| B06 | Analogue Temperature Input 4 (AT4) | 1k Pullup to SEN_5V_A |
| B07 | Knock Input 1 (KNOCK1) | |
| B08 | Universal Digital Input 3 (UDIG3) | |
| B09 | Universal Digital Input 4 (UDIG4) | |
| B10 | Universal Digital Input 5 (UDIG5) | |
| B11 | Universal Digital Input 6 (UDIG6) | |
| B12 | Battery Backup (BAT_BAK) | |
| B13 | Knock Input 2 (KNOCK2) | |
| B14 | Universal Digital Input 7 (UDIG7) | |
| B15 | Sensor 0V A (SEN_0V_A) | |
| B16 | Sensor 0V B (SEN_0V_B) | |
| B17 | CAN Bus 1 High (CAN_HI) | |
| B18 | CAN Bus 1 Low (CAN_LO) | |
| B19 | Sensor 6.3V (SEN_6V3) | |
| B20 | Analogue Voltage Input 6 (AV6) | |
| B21 | Analogue Voltage Input 7 (AV7) | |
| B22 | Analogue Voltage Input 8 (AV8) | |
| B23 | Ethernet Transmit+ (ETH_TX+) | Ethernet |
| B24 | Ethernet Transmit- (ETH_TX-) | Ethernet Green |
| B25 | Ethernet Receive+ (ETH_RX+) | Ethernet |
| B26 | Ethernet Receive- (ETH_RX-) | Ethernet Orange |
MoTeC M130 pins at a glance
- Which pins are CAN on the MoTeC M130?
- CAN Bus 1 High (CAN_HI): pin B17. CAN Bus 1 Low (CAN_LO): pin B18.
- Which pins are the injector outputs on the MoTeC M130?
- Peak Hold Injector 1 (INJ_PH1): pin A19. Peak Hold Injector 2 (INJ_PH2): pin A20. Peak Hold Injector 3 (INJ_PH3): pin A21. Peak Hold Injector 4 (INJ_PH4): pin A22. Low Side Injector 1 (INJ_LS1): pin A23. Low Side Injector 2 (INJ_LS2): pin A24. Peak Hold Injector 5 (INJ_PH5): pin A27. Peak Hold Injector 6 (INJ_PH6): pin A28. Peak Hold Injector 7 (INJ_PH7): pin A29. Peak Hold Injector 8 (INJ_PH8): pin A30.
- Which pins are the ignition outputs on the MoTeC M130?
- Low Side Ignition 1 (IGN_LS1): pin A03. Low Side Ignition 2 (IGN_LS2): pin A04. Low Side Ignition 3 (IGN_LS3): pin A05. Low Side Ignition 4 (IGN_LS4): pin A06. Low Side Ignition 5 (IGN_LS5): pin A07. Low Side Ignition 6 (IGN_LS6): pin A08. Low Side Ignition 7 (IGN_LS7): pin A12. Low Side Ignition 8 (IGN_LS8): pin A13.
- Which pins are ground on the MoTeC M130?
- Battery Negative (BAT_NEG1): pin A10. Battery Negative (BAT_NEG2): pin A11. Sensor 0V A (SEN_0V_A): pin B15. Sensor 0V B (SEN_0V_B): pin B16.
- Which pins power the MoTeC M130?
- Battery Positive (BAT_POS): pin A26.
- Which pins are the sensor supplies on the MoTeC M130?
- Sensor 5.0V A (SEN_5V0_A): pin A02. Sensor 5.0V B (SEN_5V0_B): pin A09.
MoTeC M130 pinout sheet
A printable sheet with every pin, made from the checked data on this page.
Where this comes from
Only MoTeC's own documents. Pin names and notes are written exactly as MoTeC writes them.
MoTeC datasheet
MoTeC product page (pinout tables)
MoTeC hardware manual
Plug drawing: TE Connectivity customer drawing (used for the drawing only)Third party
How we checked it
- We start from MoTeC's datasheet for this ECU.
- We read every pin again on MoTeC's product page for the ECU, and in its hardware manual where that covers the ECU. A script compares them, pin by pin.
- A pin is only shown when its pin name and full name match in every document. MoTeC sets no standard wire colours, so none are shown.
- The notes are MoTeC's own words, shown when two of its documents print them alike.
ECU Recovery is not affiliated with MoTeC. MoTeC and its product names are trademarks of MoTeC. If your harness came with its own diagram, check your wiring against it.
More MoTeC pinouts
Map locked with a password?
We unlock Haltech, MaxxECU, LinkECU, Vi-PEC, ECUMaster, Emtron and FuelTech maps. You see proof from your own file first and only pay $159.99 if it works.
Unlock a map