FuelTech FT450 的 CAN 是哪几个针脚？

CAN A (-): 针脚 15 (Yellow/Blue). CAN A (+): 针脚 16 (White/Red).

FuelTech FT450 的曲轴和凸轮轴信号输入是哪几个针脚？

CAM sync signal input: 针脚 17 (Shielded Cable (white)). Magnetic RPM sensor reference: 针脚 18 (Black Shielded Cable (White)). RPM signal input: 针脚 19 (Black Shielded Cable (Red)).

FuelTech FT450 的喷油嘴输出是哪几个针脚？

Blue output #1: 针脚 1 (Blue #1). Blue output #2: 针脚 2 (Blue #2). Blue output #3: 针脚 3 (Blue #3). Blue output #4: 针脚 4 (Blue #4). Blue output #5: 针脚 5 (Blue #5). Blue output #6: 针脚 6 (Blue #6).

FuelTech FT450 的点火输出是哪几个针脚？

Gray output #1: 针脚 8 (Gray #1). Gray output #2: 针脚 9 (Gray #2). Gray output #3: 针脚 10 (Gray #3). Gray output #4: 针脚 11 (Gray #4).

FuelTech FT450 的搭铁是哪几个针脚？

Power ground input: 针脚 7 (Black/white).

FuelTech FT450 的供电是哪几个针脚？

12V input from relay: 针脚 13 (Red).

FuelTech FT450 的传感器供电是哪几个针脚？

5V outputs for sensors: 针脚 14 (Green/Red).

针脚定义

FuelTech FT450 针脚定义

26 针插头的每一个针脚，附 FuelTech 线束的线色。点击针脚即可查看它的功能。

每个针脚都至少与 5 份 FuelTech 资料中的两份核对

26 针插头按 FuelTech 手册中的画法（手册未说明是从哪一侧看）

在图上或表格中选择任一针脚，即可查看它的功能、线色以及核对时所用的资料。

FuelTech FT450 26 针插头针脚定义

针脚	功能	线色	FuelTech 说明
1	Blue output #1	Blue #1蓝色	These outputs are usually used for injector control. When needed, they can be configured as auxiliary outputs.
2	Blue output #2	Blue #2蓝色	These outputs are usually used for injector control. When needed, they can be configured as auxiliary outputs.
3	Blue output #3	Blue #3蓝色	These outputs are usually used for injector control. When needed, they can be configured as auxiliary outputs.
4	Blue output #4	Blue #4蓝色	These outputs are usually used for injector control. When needed, they can be configured as auxiliary outputs.
5	Blue output #5	Blue #5蓝色	These outputs are usually used for injector control. When needed, they can be configured as auxiliary outputs.
6	Blue output #6	Blue #6蓝色	These outputs are usually used for injector control. When needed, they can be configured as auxiliary outputs.
7	Power ground input	Black/white黑色/白色	Directly wired to the battery negative terminal with no seams. Do not tap any other grounds to this wire, it must run clean straight to the battery negative terminal.
8	Gray output #1	Gray #1灰色	These outputs are usually used for ignition control. When needed, they can be set up as injector outputs or auxiliary outputs.
9	Gray output #2	Gray #2灰色	These outputs are usually used for ignition control. When needed, they can be set up as injector outputs or auxiliary outputs.
10	Gray output #3	Gray #3灰色	These outputs are usually used for ignition control. When needed, they can be set up as injector outputs or auxiliary outputs.
11	Gray output #4	Gray #4灰色	These outputs are usually used for ignition control. When needed, they can be set up as injector outputs or auxiliary outputs.
12	Battery negative input	Black黑色	Connected directly to the battery negative with no seams. Do not connect this wire to the chassis, engine block or head.
13	12V input from relay	Red红色	Connected to the pin 87 of the Main Relay
14	5V outputs for sensors	Green/Red绿色/红色	5V voltage output for TPS, electronic throttle and pedal sensors
15	CAN A (-)	Yellow/Blue黄色/蓝色
16	CAN A (+)	White/Red白色/红色
17	CAM sync signal input	Shielded Cable (white)白色屏蔽线	Connected to the cam sync sensor (hall or magnetic)
18	Magnetic RPM sensor reference	Black Shielded Cable (White)白色屏蔽线	Connected to the negative wire of the magnetic sensor. When OEM ECU is reading the sensor in parallel, split this wire with OEM sensor negative - Do not connect when using hall effect sensor.
19	RPM signal input	Black Shielded Cable (Red)红色屏蔽线	Connected to the crank trigger sensor (hall or magnetic) or to the distributor. To VR sensors, use the shield wire the sensor shield. To Hall sensor, do not use the shield as negative
20	Input #1	White #1白色	Sensors input
21	Input #2	White #2白色	Sensors input
22	Input #3	White #3白色	Sensors input
23	Input #4	White #4白色	Sensors input
24	Input #5	White #5白色	Sensors input
25	Input #6	White #6白色	Sensors input
26	Input #7	White #7白色	Sensors input

FuelTech 的 Map 文件被锁了？ 免费检测。付款前你会先看到来自你自己文件的验证结果。

免费检测我的 Map

FuelTech FT450 针脚速查

FuelTech FT450 的 CAN 是哪几个针脚？: CAN A (-): 针脚 15 (Yellow/Blue). CAN A (+): 针脚 16 (White/Red).
FuelTech FT450 的曲轴和凸轮轴信号输入是哪几个针脚？: CAM sync signal input: 针脚 17 (Shielded Cable (white)). Magnetic RPM sensor reference: 针脚 18 (Black Shielded Cable (White)). RPM signal input: 针脚 19 (Black Shielded Cable (Red)).
FuelTech FT450 的喷油嘴输出是哪几个针脚？: Blue output #1: 针脚 1 (Blue #1). Blue output #2: 针脚 2 (Blue #2). Blue output #3: 针脚 3 (Blue #3). Blue output #4: 针脚 4 (Blue #4). Blue output #5: 针脚 5 (Blue #5). Blue output #6: 针脚 6 (Blue #6).
FuelTech FT450 的点火输出是哪几个针脚？: Gray output #1: 针脚 8 (Gray #1). Gray output #2: 针脚 9 (Gray #2). Gray output #3: 针脚 10 (Gray #3). Gray output #4: 针脚 11 (Gray #4).
FuelTech FT450 的搭铁是哪几个针脚？: Power ground input: 针脚 7 (Black/white).
FuelTech FT450 的供电是哪几个针脚？: 12V input from relay: 针脚 13 (Red).
FuelTech FT450 的传感器供电是哪几个针脚？: 5V outputs for sensors: 针脚 14 (Green/Red).